Prtoech2u.com
 

 

How To Repair Dim Display in BenQ FP71G+ 17” LCD Monitor

benq fp71g+ lcd monitor dim display or no backlight

Normally for this BenQ FP71G+ LCD Monitor with the model of Q7T4 the major complaint was display appears for a while and then shutdown (cut off) but for this unit the complaint was dim display! That means you don’t have the chance to see the bright BenQ logo the moment power is “On”. If you look at the screen closely you could actually see the picture except that the display is very dark. If you could see the display, this means that the Main board, power board and the LCD Panel are working!

 

There could be two reasons, it is either the backlights have problem or the inverter board is faulty. Since most of the LCD Monitors in the market have top and bottom backlights, chances for both the top and the bottom backlights failed at the same time is very slim. Due to this description, I have eliminated backlights as the cause of the problem. So my concentration will be in the inverter board. Now this assumption came across my mind even before the LCD Monitor cover was removed! It is good to assume and expect which circuit that causes the problem as this will motivate you even more if the assumption is correct. Many suggestions came out from your mind and you have to decide for the best. If the assumption is wrong, then you have to ask yourself is there anyway you can improve it. Don’t put too much pressure on yourself if the assumption is way off from what you have expected, as learning from our own mistakes is the best guide for us!

 

fix lcd monitor inverter problem

benq inverter board components burnt

The moment the metal casing was removed, I could clearly see a burnt mark surrounding a transistor located at the inverter board area. My assumption was right about the inverter circuit fault and upon close inspection; the slightly dark transistor has the part number of FQU11P06. It is a P-channel FET transistor and it can be replaced with part number FU9024N. The area now has darkened and if you directly install a new transistor in it, I believe the darkened area could cause intermittent problem or total destruction again to the new transistor! Why? It is because the darkened area has become carbonized and current can flow to other circuits causing the transistor to go shorted again. In order to eliminate this problem, one has to scrap off the darkened area and due to the board is so fragile; the only way you can do is to make one hole in the area. Clean the area with thinner and install the new transistor and it should not have problem after that.

how to repair lcd monitor inverter darkness display

 Another thing that arises in my mind was is it the transistor itself has problem that goes shorted and burnt the board or other components failure that caused the transistor to go shorted? I began to check the surrounding components that have relation with the burnt transistor and found the tuning capacitor ESR value have increased, one of the push pull transistor (C5707) shorted and the Pico fuse open circuit! Upon close inspection of the capacitor, I could see bulged at one side of the capacitor.

 

bulged capacitor

 

lcd monitor bulge capacitors replacement

The value of this bad plastic film polyester type capacitor is .22 uf 160 Volts. If you test this capacitor with a digital capacitance meter, it would show about .2 uf which you may think is acceptable. If you didn’t replace this capacitor, the newly installed transistor (FQU11P06) would surely burn again. For your information, any non polarity capacitors that have the value of or higher than .1uf (104), besides test it with digital capacitance and analogue meter, I will also use ESR meter to check the ESR value of the capacitors too. In the above case, the bad cap has 47 ESR Ohm and the good one has 7.2 ESR Ohm!

 blue esr electrolytic capacitor tester

esr cap tester checking bad capacitor

Do you know that, if you owned either the dick smith or the Blue ESR meter by bob parker, besides testing the electrolytic capacitor, you can also use it to test on the non polarity capacitor too? But the non polarity capacitor value must me around .1uf or higher. The ESR meter can’t test any value which is lower than that. If you do not have any ESR meter, I guess this is the time now to invest one to speed up your repair. With the help of ESR meter, I have solved lots of intermittent problem caused by capacitors. Some intermittent capacitor problem can’t be revealed with the help from applying freezer and heat but surprisingly it can be discovered faulty by using ESR meter- this really amazed me!

 

best lcd monitor cap tester

Next, checking around all the circuit, I found another electrolytic capacitor have problem too. The faulty capacitor is located at the secondary output side and act as a filter to remove ripple along the output line. A good 1000 uf e-cap should have ESR less than .1 Ohm but the faulty one read 4.9 ESR Ohm! A new replacement of the Pico fuse, C5707 transistor, FQU11P06 FET, 1000uf 16Volts e-cap and .22uf 250V metallised polyester capacitor brought the LCD Monitor back to life again!

lcd monitor display fix

Author by: Jestine Yong

 

testing electronic componentrepair smps power supply lcd monitor repair

plasma tv repairrepair lcd tv tips

 

projection tv repair service manual

 

 

Home
Repairing Articles
Free Repairing Tips
Download Service Manual
TFT LCD Display Equivalents
Repairing Bookstore
Other Resources
Contact Us
Free Subscribe Now
Links
Site Map

LCD TV Repair

Plasma TV Repair

Projection Tv Repair

Learn Basic Electronic

Computer Repair Course

Learn Laptop Repair

CRT Tv Repair Course

LCD Monitor Repair ebook

How to testing Electronic Components like a Pro!

Power Supply Repair Guide- all types of SMPS


Testimony

1 Feb 2007

Many thanks!  I have
downloaded the file and
will - hopefully - now be
able to fix the screen.
Like your website -
very helpful...
thanks again.
- Mike

31 Dec 2006

thank you for this
great site that i
found what i
search about.
-Moomin

15 Jan 2008

Thank you very
much for your
excellent site!
I know there would
be lots of people
around the world
who will appreciate
your very neat,
well-organised site.
-Matt Straford


DONATE Help the P2U

If you find my free stuff useful, why not leave me a little something with PayPal.

Donations are greatly appreciated, and help with the costs of providing FREE service manual & server fees.